A screen door closer is the small cylinder that pulls a hinged screen or security door shut and stops it slamming.
If your door slams, a quarter turn of the adjusting screw on the end of the cylinder usually fixes it. If it won’t close at all, the closer is likely worn out. Replacements start from around $23 and take about 10 minutes to fit.
Buy A Length stocks hinged screen and security door closers in black, bronze, primrose, white, silver and other colours, plus water-filled closers for sliding screen doors.

How does a door closer work?
Most closers on Australian screen and security doors are pneumatic. A rod slides in and out of an air-filled cylinder: opening the door pulls the rod out, and a spring inside pulls it back. The trapped air slows the return, so the door closes firmly instead of banging.
One end bolts to a bracket on the door. The other end connects to a bracket on the door jamb with a removable pin. The small square washer on the rod is the hold-open washer. Slide it against the cylinder while the door is open and the door stays open.
How do you adjust a screen door closer?
Find the adjusting screw on the end of the cylinder, the end furthest from the hinge side on most installs.
- Door slams: turn the screw clockwise to slow the close.
- Door doesn’t close fully or latch: turn it anticlockwise to speed it up.
Work in quarter turns and test the door after each one. A slight speed-up over the last few centimetres helps the door latch. If you’ve turned the screw all the way and nothing changes, the seal inside the cylinder has failed. That can’t be repaired, so replace the closer.
Unsure which closer you have? Send us a photo and we’ll match it.
Why is my door slamming or not closing?
Match the symptom to the likely cause:
- The door slams no matter how you adjust it. The cylinder has lost air. Replace the closer.
- The door won’t close the last few centimetres. The closing speed is too slow, or the latch is out of line with the strike. Adjust the screw first. (Still not latching? Check the screen door lock and strike plate.)
- The rod is bent. Wind caught the door and forced it past its travel. Replace the closer. A bent rod won’t run smoothly again.
- The door rattles on its closer. A bracket has come loose. Tighten the screws, or move the bracket to fresh holes if the old ones are stripped.
- The door won’t stay open. The hold-open washer is worn or missing. A new closer comes with a new washer.

How to replace a screen door closer
You need a screwdriver or drill, a tape measure and the new closer. Allow about 10 minutes.
Step 1: Measure the old closer
Prop the door open slightly so there’s no tension on the closer. Measure the old closer from end to end and note where each bracket sits on the door and the jamb.
Choose a closer of similar length so you can reuse the existing holes. [VERIFY: confirm the Austral and standard hinged closers are the same length]
Step 2: Remove the old closer
Pull the pin at the jamb end, then unscrew the door bracket. Leave the jamb bracket in place if it’s solid and the new closer uses the same style.
Step 3: Fit the new door bracket
Screw the new door bracket into the existing holes where you can. On aluminium security door frames, use screws suited to aluminium, and don’t overtighten them or you’ll strip the thread.
Step 4: Connect the jamb end
Hold the closer level, line it up with the jamb bracket and push the pin through. The cylinder should sit roughly parallel to the floor when the door is shut.
Step 5: Adjust and test
Open the door fully and let it go. Adjust the screw in quarter turns until it closes firmly and latches without slamming.
Need the closer and the door parts in one order? Browse screen door parts.
Which closer should you buy?
Hinged screen and security doors
Hinged doors use a pneumatic closer. Security doors are heavier than fly screen doors, so a closer listed for hinged security doors, such as the Austral hinged security door closer, is the safe choice. It also works on lighter screen doors.
Match the closer colour to the door frame. Buy A Length stocks hinged closers in:
- Black, with two options (from around $24)
- Bronze, Primrose and White
- Hamersley Brown, Silver, Stone Beige and White Birch
Colour names don’t always mean an exact match between brands. Our powder coat colour guide explains why. See every closer in stock.
Sliding screen doors
A sliding door needs a different kind of closer. Buy A Length stocks the Inventco sliding screen door closer, a water-filled unit that pulls the door shut along its track. It comes in white, black and bronze, from around $290. If the door forms part of a pool barrier, self-closing and self-latching rules apply, so confirm requirements with your council or certifier before choosing hardware.
Building or rebuilding the whole door?
If the frame is past saving, Buy A Length cuts the door frame extrusions to your exact sizes as well. The closer, hinges, lock and frame can arrive in one delivery.
Start with our guide to security door frames, or build a fly screen door frame using the same cut-to-size method.
Adding a pet flap? See our pet door guide for screen doors.
Frequently Asked Questions
How do I stop my screen door from slamming?
Turn the adjusting screw on the end of the closer cylinder clockwise, a quarter turn at a time, until the door closes gently. If the screw makes no difference, the closer has lost air and needs replacing.
Why won’t my screen door close all the way?
The closer is set too slow, or the latch doesn’t line up with the strike. Turn the adjusting screw anticlockwise to speed up the close, then check the latch alignment.
Can a screen door closer be repaired?
Generally no. Once the seal inside a pneumatic cylinder fails, replacement is the fix. Hinged closers start from around $23, so replacement is usually quicker and cheaper than any repair.
What’s the difference between a screen door closer and a security door closer?
Both work the same way. A closer listed for hinged security doors is made for the extra weight of a steel-mesh or aluminium security door, and it also suits lighter fly screen doors.
Do sliding screen doors need a closer?
Most don’t have one. Where a sliding door must close itself, use a closer made for sliding doors, such as the water-filled Inventco closer. A hinged-door closer won’t work on a slider.
Get the Right Closer, Fast
Buy A Length has supplied screen door and window parts to the trade since 2006, with live stock counts on every part.
Order a replacement closer on its own or with the rest of your door parts. Orders are packed and dispatched within 1 to 2 business days.
Shop screen door closers, browse all parts, or call 1300 720 838 if you need help matching your old closer.